V-DAY SALE: Get Extra 12% Off with Coupon Code: VD12
Join Our FacebookGroup & Get Extra Discount!
V-DAY SALE: Get Extra 12% Off with Coupon Code: VD12
Join Our FacebookGroup & Get Extra Discount!
Everything is fine. The starter motor is powerful and the clamp assembly is brilliant
very good unit works well . instructions a little bit sketchy,
What a suburb bit of Kit, Don't think about it just buy one,
Parcel arrived easy fitment, works a treat,
I find a little prime of petrol in the carb makes starting even easier.
Surperb engineering, used Fema ones in the past these are half the cost,
David UK
I have not tried the item out yet as I am waiting for the base to arrive, that I ordered from your company.
Please check back with me later
The item is well made and works great once installed, but the only instructions amount to a very “polished” video that omits any sticky issues.
First, the set screw holding the flywheel flange to the crankshaft is on with lock tite. Either a big soldering gun or torch will be needed to heat it and free it. I used a small jewelers pencil flame torch. Worked great.
Second, once the rear plate is removed from the block, clean the lip of the oil pan up and use high temp red silicone to seal the new back plate when installed. Otherwise you’ll have an oil leak and get to do it again.
Adjusting the mating between the one way clutch and starter big gear by loosening the set screw will help get things aligned properly.
I’m still not totally confident of reassembly of the flywheel. The only method I figured out that worked was using the long screws provided and flipping the flywheel over with the recessed middle facing out to install it onto the starter clutch collet. You won’t have much crack left sticking out, so any thoughts of adding a pto pulley will be complicated.
Don’t try to run the starter off the ignition battery pack. The current draw is too high, and prolonged cranking will literally melt the battery tray. A dedicated starter battery is the ticket. I’m using a 9.6v NiMH pack for the starter circuit.
Again, a great product once you figure it out. It looks great and works fine. The total lack of instructions assumes a lot from the buyer.
Engine Fixing Bracket Base for TOYAN Single Cylinder Two Cylinder Engine Model Features: .The starter mounting bracket base is suitable for TOYAN...
View full detailsRC Engine Starter Kit Glow Plug Igniter Tools for 1:10 RC Car Engine HSP 80141 80142A Features:1, The tool kit includes straight screwdriver, phil...
View full details4 Stroke RC Toyan Engine Start Kit for TOYAN FS-S100 FS-S100 (W) Methanol Engine Packing List: 1 x Fuel Tank 1x 30cm Oil Tube 1 x F Shape Glow Plu...
View full detailsStart Belt / Timing Belt for Toyan 4 Stroke Engine Part FS-S100 FS-S100(W) FS-S100G FS-S100G (W) Features:1, Specialized blet part for Toyan 4 Stro...
View full details5pcs 4 Stroke RC Engine Starter Parts for TOYAN FS-S100G FS-S100G (W) Engine PartsPacking List: 1 x CDI Igniter 1x Spark Plug 1 x Fuel Tank 1 x 30...
View full detailsEverything is fine. The starter motor is powerful and the clamp assembly is brilliant
very good unit works well . instructions a little bit sketchy,
What a suburb bit of Kit, Don't think about it just buy one,
Parcel arrived easy fitment, works a treat,
I find a little prime of petrol in the carb makes starting even easier.
Surperb engineering, used Fema ones in the past these are half the cost,
David UK
I have not tried the item out yet as I am waiting for the base to arrive, that I ordered from your company.
Please check back with me later
The item is well made and works great once installed, but the only instructions amount to a very “polished” video that omits any sticky issues.
First, the set screw holding the flywheel flange to the crankshaft is on with lock tite. Either a big soldering gun or torch will be needed to heat it and free it. I used a small jewelers pencil flame torch. Worked great.
Second, once the rear plate is removed from the block, clean the lip of the oil pan up and use high temp red silicone to seal the new back plate when installed. Otherwise you’ll have an oil leak and get to do it again.
Adjusting the mating between the one way clutch and starter big gear by loosening the set screw will help get things aligned properly.
I’m still not totally confident of reassembly of the flywheel. The only method I figured out that worked was using the long screws provided and flipping the flywheel over with the recessed middle facing out to install it onto the starter clutch collet. You won’t have much crack left sticking out, so any thoughts of adding a pto pulley will be complicated.
Don’t try to run the starter off the ignition battery pack. The current draw is too high, and prolonged cranking will literally melt the battery tray. A dedicated starter battery is the ticket. I’m using a 9.6v NiMH pack for the starter circuit.
Again, a great product once you figure it out. It looks great and works fine. The total lack of instructions assumes a lot from the buyer.
Be the First to See Our New Products and Special Offers.
Copyright © 2023 EngineDIY.